|
ST公司的RHRPMPOL01是单相降压单片开关稳压器,集成了高精度内部基准电压和用于同步转换的功率MOSFET.器件采用SOI技术,对单粒子闩锁效应有良好的性能.RHRPMPOL01能输入电压3.0V到12V转换成 8V到0.85xVIN输出电压.设计用在空间应用的FPGA,DSP,MCU和ASIC的电源.器件的控制器是基于峰值电流架构,从而保证了快的负载瞬态响应和很稳定的开关频率.嵌入的积分器补偿由于输出电压波纹所引起的DC电压误差.故障管理包括非闭锁输出过压保护,过流保护和自动恢复的热保护.输出电流高达7A,工作温度-55 C 到 +125 C,可编开关频率从100kHz到1MHz.RHRPMPOL01总离子剂量为100 krad,无单粒子闩锁效应高达70 MeV/mg/cm2 (@ VCC up to 7 V),SEU-SEFI特性高达VCC 7V,无质子.主要用在空间应用的点负载稳压器,FPGA,DSP,CPU和ASIC电源以及低压高密度分布电源系统.本文介绍了RHRPMPOL01主要特性,框图,典型应用电路图及其
外用元件表.以及评估板EVAL-RHRPMPOL01主要特性,电路图,材料清单和PCB设计图.
The RHRPMPOL01 is a single phase, step-down monolithic switching regulator with
high precision internal voltage reference and integrated power MOSFETs forsynchronous conversion. The device has been developed using SOI technology thatoffers good performance against SEL effect.
The regulator converts 3.0 V to 12 V input voltage to 0.8 V to (0.85xVIN) outputvoltage. It has been designed to supply FPGA, DSP, MCU and ASICS in general forspace applications.
The controller is based on peak current mode architecture, which ensures a fast load
transient response and very stable switching frequency. An embedded integratorcompensates the DC voltage error due to the output voltage ripple. The faultmanagement consists of not-latched output overvoltage protection, overcurrentprotection and auto recovery thermal protection.
RHRPMPOL01主要特性:
• 3.0 V to 12 V input operating voltage range (target radiation performanceguaranteed at VCC up to 7 V)
• 0.8 V to (0.85xVIN) output voltage range
• Up to 7 A output current
• Wide operating temperature range -55 C to +125 C
• Single supply
• Integrated N-channel MOSFETs for synchronous step-down conversion
• Integrated BOOT diode
• Programmable switching frequency: from 100 kHz to 1 MHz
• Fast load transient response and simple loop compensation based on peakcurrent mode control loop
• Easy synchronization with 180 out-of-phase (up to 2 ICs) management
• Current sharing configuration for higher load requirements
• Lossless current sensing based on sense-FET
• Not-latched output overvoltage protection
• Adjustable output overcurrent protection
• Input undervoltage protection
• Latched overtemperature protection
• Power Good output pin
• Programmable soft-start with increased current capability
• Hermetic ceramic package qualified for space applications FLAT-28
• Target radiation performance:
– Total ionizing dose: 100 krad
– Tested ELDRS-free
– SEL-free up to 70 MeV/mg/cm2 (@ VCC up to 7 V)
– SEU-SEFI characterized up to VCC 7 V
– Proton free
– No performance degradation due to SET
– QMLV qualification ongoing
RHRPMPOL01应用:
• Point of load regulation for space application
• FPGA, DSP, CPU and ASICS supply
• Low voltage, high density distributed power systems
图1.RHRPMPOL01框图
图2.RHRPMPOL01典型应用电路图
图2应用电路图中的外用元件表:
评估板EVAL-RHRPMPOL01
EVAL-RHRPMPOL01 evaluation board of radiation hardened 7 A monolithicsynchronous switching regulatorThis user manual provides an overview of the use of the EVAL-RHRPMPOL01 evaluation board. It has been developed andoptimized for a typical application of the RHRPMPOL01 device, a single phase, step-down monolithic switching regulator withhigh precision internal voltage reference and integrated power MOSFETs for synchronous conversion. The regulatorRHRPMPOL01 converts 3 V - 12 V input voltage to 0.8 V - (0.85xVIN) output voltage. The controller is based on a peak current
mode architecture, which ensures a fast load transient response and very stable switching frequency. An embedded integratorcompensates the DC voltage error due to the output voltage ripple.
评估板EVAL-RHRPMPOL01主要特性:
• Input operating voltage: 5.0 V
• Output voltage: 1.2 V
• Output current: up to 5 A
• Enable input voltage: 2.5 V
• Switching frequency: 500 kHz
• Output overcurrent protection: 10 A
• Easy synchronization with 180 out-of-phase (up to 2 ICs) management
图3.评估板EVAL-RHRPMPOL01外形图
图4.评估板EVAL-RHRPMPOL01电路图
评估板EVAL-RHRPMPOL01材料清单:
图5.评估板EVAL-RHRPMPOL01 PCB设计图:顶层装配
图6.评估板EVAL-RHRPMPOL01 PCB设计图:顶层
图7.评估板EVAL-RHRPMPOL01 PCB设计图:中间层1
图8.评估板EVAL-RHRPMPOL01 PCB设计图:中间层2
图9.评估板EVAL-RHRPMPOL01 PCB设计图:底层
|
